INSTALLING A BATH TUB

Installing A Bath tub

Installing A Bath tub

Blog Article

Book Services

Presented here in the next paragraph yow will discover more incredibly good content in regards to Tools You Need to Install a New Bathtub .


How to Install a Bathtub: Install an Acrylic Tub and Tub Surround
Mounting a tub isn't exactly brain surgery, but it does call for solid plumbing, woodworking, and occasionally, tiling skills. Replacing an old bath tub with a brand-new one is also a reasonably tough project. If the old bathtub is readily accessible, the job can move easily; if you need to open a wall surface to remove the old bathtub as well as position the brand-new bathtub, the job is much harder. In either instance, the job is within a home handyman's abilities, although you will require a helper to vacate the old tub and also set in the brand-new one. Ensure you have actually qualified on your own for the job and also are comfortable trying it. Rather than employing a contractor to take control of a halfway-completed project, it is much better to consider utilizing one before you start. Opportunities are you may require an expert plumber to make tube connections.
This write-up will aid you install a brand-new bath tub in your restroom if you have currently bought a new bathtub and don't require to change the plan of your previous water supply pipes.
Your devices and material list should make up the following:
  • New Bath tub
  • Hammer

  • Pipe Wrenches

  • Prybar

  • Shatterproof glass

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Knife

  • Tape Measure

  • Pipe Caps


  • Planning for the Installation


    First of all, the supporting structure supplied with the bath must be fitted (if called for) according to the manufacturer's directions. Next off, fit the taps or mixer to the bathtub. When fitting the faucet block, it is essential to make certain that if the faucet comes with a plastic washer, it is fitted in between the bathroom and also the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets unit to avoid stress on the bath tub.
    Fit the adaptable tap connectors to the bottom of the two faucets making use of 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet through the hole in the bath. Use the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
    Next off, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. Ensure you use all of the supplied washers.
    Link the trap to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Link the bottom of the overflow tube in a similar manner.The bath should now be ready to be fitted in its last position.

    Removing Old Taps


    If you require to change old faucets with brand-new ones as a part of your installment, then the first thing you ought to do is disconnect the supply of water. After doing so, turn on the taps to drain pipes any type of water staying in the system. The process of removing the existing taps can be fairly bothersome as a result of the restricted access that is frequently the case.
    Make use of a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipelines to the faucets. Have a fabric ready for the remaining water that will certainly originate from the pipes. Once the supply pipelines have actually been eliminated, use the same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary taps from turning throughout this process. As soon as the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleansed of any type of old securing substance.
    Before moving on to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new taps, after that a shank adapter is required for the brand-new taps to fit.

    Mounting the Bathtub


    Utilizing both wooden boards under its feet, position the bathtub in the called for position. The wood boards are helpful in uniformly spreading the weight of the tub over the area of the boards rather than concentrating all the weight onto four tiny points.
    The next objective is to make certain that the tub is leveled all round. This can be attained by inspecting the level and changing the feet on the bath tub till the spirit level checks out degree.
    To set up faucets, fit the bottom of the furthest adaptable tap port to the appropriate supply pipe by making a compression sign up with; after that do the same for the other faucet.
    Switch on the water system and also check all joints as well as brand-new pipework for leaks and tighten them if needed. Load the bathtub and also examine the overflow outlet and the typical electrical outlet for leakages.
    Finally, deal with the bathroom paneling as defined in the supplier's instruction manual. Tiling as well as sealing around the tub must wait up until the bath tub has been used at least once as this will settle it into its last placement.

    Fitting New Taps


    If the tails of the new taps are plastic, then you will certainly need a plastic port to stop damages to the thread. One end of the connector fits on the plastic tail of the tap as well as the other end supplies a connection to the existing supply pipes.
    If you need to fit a monobloc, then you will require decreasing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
    Next, place the faucet in the placing opening in the bath/basin making certain that the washing machines are in place between the faucet and the sink. Secure the faucet in position with the supplier supplied backnut. Once the tap is securely in position, the supply pipelines can be linked to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with typical tap connectors. The previous type needs to be connected to the faucet finishes initially, tightening only by hand. The supply pipes can later be connected to the various other end. Tighten up both ends with a spanner after both ends have been linked.

    Tiling Around the Bathtub


    In the area where the bath meets the floor tile, it is needed to secure the joins with a silicone rubber caulking. This is essential as the fitting can move sufficient to split a rigid seal, causing the water to pass through the wall surface between the bath and the tiling, bring about issues with moisture and possible leakages to the ceiling below.
    You can choose from a variety of coloured sealers to blend in your fixtures and also installations. They are sold in tubes and cartridges, and also can sealing gaps approximately a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with spins of soaked newspaper or soft rope. Bear in mind to always load the bath tub with water before sealing, to permit the motion experienced when the tub remains in use. The sealer can split fairly very early if you do not take into consideration this movement prior to sealing.
    Alternatively, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally quickly readily available on the marketplace. It is advisable to fit the floor tiles utilizing waterproof or water resistant adhesive as well as grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    Tools You Need to Install a New Bathtub

    We had been made aware of that report about A Step-by-Step Guide to Installing a Bathtub through an acquaintance on a different web page. Sharing is caring. One never knows, you will be helping someone out. Thanks a lot for going through it.




    Schedule Service Pickup


    Report this page